Black Ninja

By TaterrsFPV on Mar 22, 2020

7  302  2

This will be the last build for a few months as the weather will be breaking soon and then its time to fly more build less. I went all out on parts this build. Hope to gets some good flights w/ this one. Cut down weight and and went w/ a caddx Turtle V2. THanks to Eightamrock for the Bracket. Mounting the PDB for turtle went in real nice. https://www.thingiverse.com/thing:2870082/comments . Weight comes in @ 642.7g.

Photos

Part List

Frame

Armattan Rooster 6" Freestyle Frame (15 builds)
Racedayquads.com
$95.00

Flight Controller

iFlight SucceX F7 TwinG V1.0 BlueTooth BT STM32F722RET6 Flight Controller(Dual ICM20689) with 30.5*30.5mm mounting hole for FPV (2 builds)
Banggood.com
$58.56

ESCs

iFlight Succex 32Bit 50A 30x30 4in1 ESC (3 builds)
Racedayquads.com
$49.99

Motors

4 x BrotherHobby Avenger V2 2507 Drone Motors (All KV's)
Cyclonefpv.com
$87.96

Propellers

Gemfan Flash 6042 Tri-Blade 6" Prop 4 Pack - Choose Your Color (11 builds)
Racedayquads.com
$3.99

FPV Camera

CADDX Turtle V2 TURBO EYES LENS (63 builds)
Pyrodrone.com
$64.99

FPV Transmitter

RDQ Mach 3 Video Transmitter 25-1000mW VTX 2-6S - U.FL or MMCX (119 builds)
Racedayquads.com
$24.99

Antenna

Foxeer Lollipop V3 5.8GHz 10CM Long Range SMA Antenna 2 Pack - RHCP - Choose Your Color (10 builds)
Racedayquads.com
$19.90

Receiver

FrSky R9MM OTA SBUS Long Range 900MHz Micro Receiver (ACCESS) (45 builds)
Racedayquads.com
$23.50

Batteries

CNHL Black Series 1100mAh 22.2V 6S 100C Lipo Battery (29 builds)
Chinahobbyline.com
$27.99

Radio

FrSky Taranis QX7S 2.4GHz RC Transmitter - Carbon or Blue (50 builds)
Racedayquads.com
$184.99

Goggles

Fat Shark Dominator HD2 Terminator Edition FPV Goggles (4 builds)
Getfpv.com
$399.99

HD Camera

GoPro HERO5 Session (6 builds)
Bhphotovideo.com
See Site

Video Receiver

FuriousFPV True-D X (for Fatshark Dominators) - RedSKU: FPV-RX-TRUDX (3 builds)
Furiousfpv.com
$119.95

Radio Module

FrSky R9M Module (69 builds)
Pyrodrone.com
$49.99
Show stores (8)

Discussion

Sign in to comment

dafunk   Mar 24, 2020  

Nice build and Interesting camera mount... did you print the file without modification ?
how is the board screwed to the printed mount ? couldn't figure it on the thingiverse.

TaterrsFPV   Mar 24, 2020 

No mods. Just M2 screwz / nuts and standoffs and thanks for the like.

Guides & Reviews

26 1,241  11
17 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
42 4,827  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more