FlosStyle Mamba LS2207-1600KV

By yds on Jun 18, 2020

5  145  0

MAMBA 506 is installed backwards to make the XT60 come up through the top plate right behind the GoPro mount. I took all the wires out of the FC end and rearranged them so motors 4&1 and 2&3 were swapped in the harness.

Maiden AutoTune @620g AUW

Photos

Part List

Frame

FlosStyle
Pyrodrone.com
See Site

Flight Controller

HGLRC 30.5x30.5mm AIRBUS F4 Flight Control Board Betaflight OSD (2 builds)
Hglrc.com
$34.99

ESCs

Diatone Mamba F50 PRO 50A 6S DSHOT1200 4-in-1 ESC (9 builds)
Getfpv.com
$44.99

Motors

4 x EMAX LS2207 Lite Spec Brushless Motor (CW Thread)
Emax-usa.com
$35.96

Propellers

DALProp NEPAL N1 51435 5.1 Inch Freestyle Sweepback 3-Blade Propeller POPO (2 Pairs ) - Crystal Red (3 builds)
Heli-nation.com
$2.99

FPV Camera

Foxeer Micro Razer FPV Camera PAL NTSC Switchable 1.8mm Lens 4:3 Ratio - Black (2 builds)
Heli-nation.com
$17.90

FPV Transmitter

AKK FX3 FPV VTX (112 builds)
Akktek.com
$18.99

Antenna

Foxeer 5.8G Lollipop 3 RHCP Angle MMCX 2.5DBi Omni Antenna (2pcs) - GREEN (2 builds)
Heli-nation.com
$19.99

Receiver

Team BlackSheep TBS Crossfire Nano RX (SE) - FPV Long Range Drone Receiver (334 builds)
Heli-nation.com
$29.99

Batteries

AKK FX3 FPV VTX (112 builds)
Akktek.com
$18.99

3D Printed

Hyperlite Flowride Session case by Davschall
Thingiverse.com
See Site

3D Printed

Floss Fixed Camera Mount by WaFL_FPV
Thingiverse.com
See Site

Hardware

Aluminium M3 Screw (Round) Spacer (Titanium / 10pcs) (5 builds)
Myrcmart.com
$1.99

Hardware

Hex Flange Locknuts M3 (Slip-Resistant / Carbon Steel / 10pcs)
Myrcmart.com
$0.99

Hardware

Suleve™ M3SS4 100Pcs Metric M3 304 Stainless Steel A2 Button Head Hex Socket Cap Screw Bolt
Banggood.com
See Site

Misc Parts

US $9.0 10% OFF|BEITIAN, small size chipset GPS module, GPS GLONASS Dual GNSS module with 4M FLASH, 20mm*20mm*6mm,BN 200|GPS Rec
Aliexpress.com
See Site
Show stores (10)

Discussion

Sign in to comment

Guides & Reviews

39 4,001  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more
28 7,803  38
Nov 30, 2019

In late 2019 DJI made inroads into the FPV scene with their remarkable low-latency digital system. It gave us a 720p video feed with latency on-par with the status quo, analog video. Traditionally we've used analog video systems for low-latency video, but the video quality is far from ideal. It's a trade-off we've been willing to accept for the control. Now we've got the best of both worlds and what..

Read more