BeeRotor 130

By miromir237 on Mar 13, 2017

9  510  0

This is my most clean build thanks to BRF3 and BRPDB combination. The only downside I see is presence of JST SH 1.25 connectors on FC which leads to soldering thin wires from receiver and vtx.
The Turnigy 3S 1000mAh battery is bit heavy but it's the only I have right now. I plan to use Turnigy Nano-Tech 3S 850mAh.

One of the motors died (broken windings wire) so I replaced the motors with Emax RS1306 3300kv. They are very powerfull. I love them.
I currently use XF Power 850 mAh 70C 4S battery. I do not believe it is 70C. Full throttle and voltage drops rapidly. I will be testing 4S XF Power 550 mAh 70C. I do not expect better performance but less weight.


Part List


BeeRotor BR130 Carbon Fiber Mini FPV Racing Frame

Flight Controller

BeeRotor F3 (AIO) Flight Controller with OSD (17 builds)


DYS XSD 20A 3-4S ESC BLHeli_S Supports Dshot600 Dshot300 For RC Drone FPV Racing Multi Rotor (2 builds)


DYS 1306 3100KV BX Series Brushless Motor for RC Drone FPV Racing Multi Rotor (9 builds)


2 Pairs DALPROP 3045 T3045 3 Blade PC Propeller CW CCW For 100 120 150 RC Multirotor (14 builds)

FPV Camera

Eachine 1000TVL 1/3 CCD 110 Degree 2.8mm Lens Wide Voltage 5-20V Mini FPV Camera NTSC PAL Switchable (37 builds)

FPV Transmitter

Eachine TX526 5.8G 40CH 25MW/200MW/600MW Switchable AV Wireless FPV Transmitter RP-SMA Female (122 builds)


Aomway 5.8GHz FPV 4 Leaf Clover AV Transmission RHCP Antenna 1 Pair Blue Red w/Canopy For RC Drone (112 builds)


Flysky FS-A8S FS A8S V2 2.4G 8CH Mini Receiver with PPM i-BUS SBUS Output (91 builds)


Turnigy nano-tech 850mAh 4S 45~90C Lipo Pack

Power Distribution

BeeRotor Power Distribution Board V2.0(w/ 5V,12V Out put) (11 builds)


FrSky Taranis X9 Lite 2.4GHz 24CH ACCESS ACCST D16 Mode2 Classic Form Factor Portable Transmitter for RC Drone (10 builds)


(PRE-ORDER) DJI Digital FPV Goggles - Ultra Low Latency 720p 120FPS Digital HD (73 builds)

HD Camera

GoPro Hero5 Session (196 builds)

Misc Parts

5V Buzzer Alarm Beeper With Cable for Eachine QX70 QX90 QX95 QX95S NAZE32 F3 DIY Micro Brushed FPV Racer (15 builds)

Misc Parts

RP-SMA Male to RP-SMA Female Adapter Right Angle RF Connector For FPV RC Drone (4 builds)

Radio Module

FrSky R9M Transmitter Module (69 builds)

Battery Charger

ISDT Q6 Plus 300W 14A MINI Pocket Battery Balance Charger (56 builds)

Soldering Iron

TS100 Portable Programmable Smart Soldering Iron (161 builds)


Torvol Quad Pitstop Backpack PRO (4 builds)

Misc Supplies

TrueRC X-AIR 5.8GHz Crosshair Antenna (RHCP) (4 builds)
Show stores (7)


Sign in to comment

Guides & Reviews

39 3,913  46
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more
28 7,731  38
Nov 30, 2019

In late 2019 DJI made inroads into the FPV scene with their remarkable low-latency digital system. It gave us a 720p video feed with latency on-par with the status quo, analog video. Traditionally we've used analog video systems for low-latency video, but the video quality is far from ideal. It's a trade-off we've been willing to accept for the control. Now we've got the best of both worlds and what..

Read more