TC-R220 kissed by DYS

By miromir237 on Jul 20, 2017

6  297  0

An attepmt to build with some quality parts.

Frame is of decent quality. Carbon is cut very well. Supplied harware is OK. The FPV camera plates are no as tight as they should be and there is a little play. I would also appreciate some gummy protection for vtx antena and power wires from the carbon cutouts.

I have strugled with mouning the DYS F4 FC and 4 in 1 ESC combo a little bit because of the dampening grumets. At the end I did not used them and replaced them with Realacc M3*7+4.5 FC Anti-Vibration Fixed Screws together with nylon screws and o-rings combination.

The VTX and MonsterV2 wires are compatible but the positive and negative was switched on camera and I almost burnt it. Fortunately the LC filter on VTX saved my day.

Thanks to Project Blue Falcon videos I had zero troubles connecting XSR receiver and setting my new QX7. Kudos to him. May he reset in peace. I will really miss him.

I tried to avoid soldering little wires as much I could and that proved to be a good thing for me.

After all this was nice build.


Part List


TC-R180 TC-R220 TC-R260 Carbon Fiber Frame Kit 4.0mm Frame Arms (11 builds)

Flight Controller

Upgrade DYS 30.5x30.5mm F4 Pro V2 Flight Controller AIO OSD & 5V 9V 3.3V BEC & Current Sensor (139 builds)


DYS F20A 20amp 4 in 1 BLHeli_S ESC 2-4S BB2 BEC 5V/12V 3A Dshot600 Oneshot125 Oneshot42 Multishot RC Drone (22 builds)


Two Pair DYS SE2205 2300KV 3-5S Brushless Motor CW CCW for Multicopters 2CW 2CCW (2 builds)


4 x DYS 3-blade 5040 5x4 Inch Bullnose Propeller CW CCW for 200 210 230 250 280 RC Drone (2 builds)

FPV Camera

Page Not Found - (78 builds)

FPV Transmitter

FT48X 5.8G 48CH 0.25/25/200/600mW Adjustable Video Transmitter VTX Raceband For FPV Racer RC Drone (19 builds)


Realacc 5.8G 5dBi 50W Omni Directional Omni FPV Pagoda Antenna LHCP/RHCP SMA/RP-SMA For FPV RC Drone (48 builds)


FrSky XSR 2.4GHz 16CH ACCST Receptor S-Bus CPPM Salida Soporta X9D X9E X9DP X12S X Series (15 builds)


2 x AHTECH Infinity 4S 14.8V 1500mAh 85C Graphene LiPo Battery XT60 Support 15C Boosting Charger (78 builds)


2 x Giant Power Dinogy 1300mAh 14.8V 4S 65C LiPo Battery For RC Models (15 builds)


FrSky Taranis Q X7S Digital Telemetry Radio System 2.4GHz ACCST (EU) (10 builds)


Fat Shark Dominator HDO FPV Goggles (64 builds)

HD Camera

GoPro HERO7 Black Action Camera (31 builds)

Misc Parts

6mm Snakeskin Net Braided Protection Rope for Brushless ESC 5M (3 builds)

Misc Parts

4 PCS Realacc M3*7+4.5 Flight Controller Anti-Vibration Fixed Screws for RC Drone FPV Racing (48 builds)

Misc Parts

CA$4.02 V2.0 470uf Anti-interference Parallel Capacitor Plate Capacitance Board 1-6S LiPo For Mini ESC RC Parts from Toys Ho (7 builds)

Misc Parts

2 x RJX Hobby Magic Tape Bulletproof Vest Material Tie Down Strap for RC Battery (3 builds)

Misc Parts

5pcs 32cm colorful Universal Antenna Tube for RC Models

Misc Parts

Lantian DIY Colorful Paint Ink Marker Drawing Doodling Pen for FPV Racer Drone 9 Color (6 builds)

Video Receiver

Furious True-D V3.5 Diversity Receiver System Firmware 3.8A (FatShark Attitude Version)SKU: FPV-RX-TRUD3.8A (16 builds)

Radio Module

FrSky R9M Transmitter Module (49 builds)

Battery Charger

ISDT Q6 Plus 300W 14A MINI Pocket Battery Balance Charger (51 builds)

Soldering Iron

TS100 Portable Programmable Smart Soldering Iron (75 builds)


Torvol Quad Pitstop Backpack PRO (4 builds)


TBS Diamond Antenna (12 builds)

Misc Supplies

TrueRC X-AIR 5.8GHz Crosshair Antenna (RHCP) (4 builds)
Show stores (7)


Sign in to comment

Guides & Reviews

28 2,947  21
22 days ago

You've probably heard the term "Cinewhoop". Traditionally it's a 3" ducted quad capable of carrying a GoPro Hero7 Black at a low 10 degree angle. More recently the term "Cine" has been applied to a number of RTF quads ranging from 85mm to 3". They all focus on their HD capability, but none compare to the stabilization of Hypersmooth (only available on the Hero7 Black). This is what really offers that..

Read more
41 5,328  42
May 31, 2019

A couple years ago I built the TransTEC Frog and since then I've been patiently waiting for another TransTEC frame to catch my eye. Fast forward to today and the TransTEC Laser S is that frame. It's a 82g racing frame that features 6mm arms, a TPU micro cam mount, 30.5mm and 20mm stack mounts and 3K carbon and 7075 hardware. My goal here was to build a high quality 6S racer at a reasonable price. I'd..

Read more