Shendrones Squirt V2.1

By Buzzin G FPV on Nov 24, 2019

10  1,309  8

Another clean build from the dirty old hobby mat :D

Shendrones Squirt V2

Full Spec:
Frame: ShenDrones Squirt V2.1
FC: Helio Spring Mini 20x20 - Emuflight with Pierre config
ESC: Aikon AK32 20x20 - Dshot 1200
Motors: T-Motor F1507 3800kv
FPV Cam: Predator V4 Micro
VTX: ImmersionRC Tramp
Antenna: AXii
Rx: Crossfire Nano with Immortal T
Props: HQ Cinewhoop props
LiPo: 1300mah 4S Tattu R-Line

[

]
[
]

Photos

Part List

Frame

Squirt V2.1 by ShenDrones (2 builds)
Drone-fpv-racer.com
$118.34

Flight Controller

HelioRC SPRING Mini 20x20mm - IMU-F F4 Flugsteuerung
Flyingfolk.com
$51.97

ESCs

Aikon AK32PIN 4in1 35A 6S (4 builds)
Drone-fpv-racer.com
$70.96

Motors

4 x T-Motor F1507-3800KV
Drone-fpv-racer.com
$94.28

Propellers

HQProp Durable Duct-3 for Cinewhoop (2x CW + 2xCCW)
Drone-fpv-racer.com
$3.54

FPV Camera

Foxeer Predator Micro V4 (2 builds)
Drone-fpv-racer.com
$47.27

FPV Transmitter

ImmersionRC Tramp HV - 5.8Ghz Video Transmitter
Drone-fpv-racer.com
$37.79

Antenna

Lumenier AXII 2 5.8GHz SMA -RHCP Antenna (2pcs)
Drone-fpv-racer.com
$52.00

Receiver

TBS Crossfire Nano RX (SE) (3 builds)
Drone-fpv-racer.com
$40.16

Batteries

Tattu R-Line 4S 1300mAh 95C Lipo Battery
Drone-fpv-racer.com
$26.05
Show stores (2)

Discussion

Sign in to comment

sedwo   Jun 24, 2020  

I just received my DJI Squirt frame and noticed that the ducts don't have any slits in them for the motor wire to pass under.
Did you add them or simply bolt the ducts over the wiring on the arms?

One1Tick   Dec 28, 2019  

Hi, nice setup! Did you change something on the Pierre's preset ? I tried emu with pierre preset but it flyes not so great on my squirt... However the preset is grate on my 5" and another 3". Thanks a lot.

CoffeeMan   Nov 24, 2019  

Badass! Flight footage would be awesome. I'm looking to build one myself.

Buzzin G FPV   Nov 25, 2019 

will get some flight footage up soon buddy. its been raining for days here, as soon as the rain stops i'll get it out for maiden flight

CoffeeMan   Dec 22, 2019 

Fu** yes! great footage!

DoubleJackOnTap   Nov 25, 2019  
1

That is super nice and clean.  I'm envious of your solder joints.   Does the braided motor wire have any advantages other than aesthetics?

Buzzin G FPV   Dec 04, 2019 
1

thanks man :) on signal wires braided/twisted wires helps prevent cross talk between wires, not sure if it has the same effect on motor wires....does look good though lol

tonnyken   Nov 28, 2019  

Your feedback helps me a lot, A very meaningful event, I hope everything will go well happy wheels

Guides & Reviews

53 4,024  44
25 days ago

For the longest time we've been limited to 3 to 4 minutes of flight and lots and lots of batteries. With more efficient motors and frame designs it's now possible to push the envelope much further. This guide will walk you through the process of building a micro long range quad capable of flying 8-30 minutes and more than 4km. The build is moderately difficult, but with the right tools and steady hands..

Read more
35 2,613  18
Jul 20, 2020

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more