Iflight DC5 PinkFlyd 5"

By lb2e on Apr 07, 2020

14  422  7

This is my first quad and i like it for this reason no propelers view, good motor and really strong frame at the impact.
I do for this frame an air cooling system for Dji air unit to decrease temperature during flight.
You can find on https://www.thingiverse.com many 3D printed part i do for this frame.
Hope you enjoy this design.

Photos

Part List

Frame

Chssis iFlight DC5 HD
Studiosport.fr
$59.00

Flight Controller

KakuteF7 HDV (3 builds)
Shop.holybro.com
$38.00

ESCs

Tekko32 F3 4in1 ESC(45A) (3 builds)
Shop.holybro.com
$56.00

Motors

4 x XING X2207 2-6S FPV NextGen Motor (unibell)
Shop.iflight-rc.com
$79.96

Propellers

HQProp DP 5x4.3x3V1S Light Purple Propeller - 3 Blade (2CW+2CCW/Bag) (345 builds)
Getfpv.com
$3.60

FPV Camera

DJI Digital HD FPV Camera (88 builds)
Getfpv.com
$59.99

FPV Transmitter

DJI Digital HD FPV Air Unit Module (79 builds)
Getfpv.com
$99.99

Antenna

DJI Digital FPV Air Unit Elbow MMCX Antenna 2 Pack (40 builds)
Racedayquads.com
$15.00

Receiver

FrSky R-XSR 2.4GHz 16CH ACCST Micro Receiver w/ S-Bus & CPPM (876 builds)
Getfpv.com
$20.99

Batteries

Tattu R-Line Version 3.0 1300mAh 22.2V 120C 6S1P Lipo Battery Pack with XT60 Plug (51 builds)
Pyrodrone.com
$36.99

Radio

Jumper T18 Multi JP5IN1 Protocol Open TX Transmitter
Graysonhobby.com
$159.99

Goggles

(PRE-ORDER) DJI Digital FPV Goggles - Ultra Low Latency 720p 120FPS Digital HD (98 builds)
Racedayquads.com
$529.00

3D Printed

COOLING SYSTEM DJI AIR UNIT for IFLIGHT DC5 HD by Lboy
Thingiverse.com
See Site

3D Printed

PRINT FOR IFLIGHT DC5 LANDING PAD, CAPACITOR AND BUZZER SUPPORT, BUMPER by Lboy
Thingiverse.com
See Site

3D Printed

iflight DC5 FUSELAGE by Lboy
Thingiverse.com
See Site

Misc Parts

Beitian Smallest Mini Dual GLONASS+GPS BN-180 Micro Double GPS Antenna Module UART TTL For CC3D F3 RC Drone Airplane (17 builds)
Banggood.com
$12.19

Misc Parts

Panasonic 1000uF 35V Low ESR Capacitor for ESC Noise Reduction (114 builds)
Racedayquads.com
$1.49

Battery Charger

Chargeur SkyRC Q200 Quattro AC/DC Charger (max 2x100W + 2x50W) Bluetooth (7 builds)
Drone-fpv-racer.com
$218.56
Show stores (10)

Discussion

Sign in to comment

kwadkenstine   Apr 09, 2020  
1

Hi, I used your cooling duct print on my build , AIR HAMMER , works well , Thank you!!!.
Unfortunately i smashed it pretty hard , but the print survived to be used again soon , might put it on my next build.
Cheers

lb2e   Apr 10, 2020 

thank you, i'm very happy if you are. if you have a picture just for me, it will be great.

lb2e   Apr 10, 2020 

Are you interrested about fusekage of DC5 like i do?

Jodie Froster   Apr 08, 2020  
1

Nice prints! I have been thinking about making "shark gills" for the air unit for months

lb2e   Apr 08, 2020 

what kind of frame do you have? i do this "shark gills", for DC5 IFLIGHT, Armattan BADGER and Catalyst machineworks BANGGOD (pictures).

Aurora130   Apr 07, 2020  

That cowling you designed makes the quad look so mcuh better! Awesome build!

lb2e   Apr 07, 2020 

thank you,.

Guides & Reviews

60 4,914  52
Aug 26, 2020

For the longest time we've been limited to 3 to 4 minutes of flight and lots and lots of batteries. With more efficient motors and frame designs it's now possible to push the envelope much further. This guide will walk you through the process of building a micro long range quad capable of flying 8-30 minutes and more than 4km. The build is moderately difficult, but with the right tools and steady hands..

Read more
36 2,718  19
Jul 20, 2020

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more