Blue Apex

By Sachatouille on Jul 29, 2020

3  81  0

This is my first freestyle and 6s drone, so enjoy it.
For more pictures and flight follow me on

Happy flying ; )

ps: on this build there a capacitor and a GoPro that is not on the pictures, both of them with a specific mount, Thingiverse links in the 3D printing part.


Part List


Apex 5" Base Frame Kit (10 builds)

Flight Controller

RADIX LI Flight Controller - brainfpv (22 builds)


XRotor 40A 4in1 (20x20) BLHeli-32 DShot1200 for FPV Pilots - HOBBYWING North America (19 builds)


5 x T-Motor F60 PRO IV - 1750Kv


10 x HQ Freestyle Prop 5x4.3x3V2S (2CW+2CCW) - PC

FPV Camera

2 x Foxeer Falkor 2 Mini 1200TVL FPV Camera

FPV Transmitter

TBS Unify Pro 5.8 Ghz HV - SMA (5 builds)


Antennes TBS Triumph PRO - RHCP (SMA) (2 builds)


TBS Crossfire Nano RX - FPV Long Range Drone Receiver (698 builds)


8 x Batterie Lipo Tattu R-Line 6S 1300mAh 120C - Version 3.0 (4 builds)


FrSky ACCST Taranis Q X7 Transmitter 2.4G 16CH Mode 2 White Black International Version for RC Drone (218 builds)


FatShark Dominator HDO 4:3 OLED Display FPV Video Goggles 960x720 for RC Drone (119 builds)

3D Printed

ImpulseRC Apex - GoPro and Cap Mount by RV_FPV
See Site

HD Camera

(Renewed) GoPro Hero5 Session (16 builds)

Misc Parts

Motor Wire Shield 10mm (10pcs)

Misc Parts

Vifly Finder 2 - Buzzer Autonome (3 builds)

Misc Parts

Condensateur Panasonic Low ESR 1000uF 35V (2 builds)

Video Receiver

Furious True-D Diversity Receiver Module 5.8GHz System V3 Firmware 3.9 (24 builds)

Radio Module

TBS Crossfire Micro TX V2 (114 builds)

Battery Charger

SkyRC T200 200W AC/DC Charger (4 builds)

Battery Charger

ISDT Q6 Lite 200W 8A MINI Pocket Battery Balance Charger for 2S-6S Lipo Battery (23 builds)

Soldering Iron

MINI TS100 Digital OLED Programmable Interface DC5525 Soldering Iron Station Built-in STM32 Chip (170 builds)


Ethix Tool Case (9 Pcs) (4 builds)
Show stores (9)


Sign in to comment

Guides & Reviews

24 1,227  11
17 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
42 4,820  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more