Rathix 6S

By M490fpv on Aug 11, 2020

10  304  5

This Ethix cinerat was fun to build and really fun to fly!
I used some pistachio green 98A(Fillamentum Flexfill) and dark gray 95A TPU on this build.
I also remixed my motor soft mount/wire guards and GoPro Hero 7 mount design to this build. STL's are here: https://www.thingiverse.com/thing:4567014

Stock vista antenna is too short to reach the back, when air unit is installed to front, so i used some cable extension and TrueRC matchstick antenna.
This way the longer antenna is also not hiding behind the lipo, should increase the video quality.

Photos

Part List

Frame

ETHIX CINERAT (CARBON AND HARDWARE PARTS)
Drone-fpv-racer.com
$45.24

Flight Controller

Contrôleur de vol Aikon F7 Mini HD V2
Drone-fpv-racer.com
$47.57

ESCs

Aikon AK32PIN 4in1 35A 6S (3 builds)
Drone-fpv-racer.com
$69.67

Motors

4 x T-Motor F1507-2700KV (3 builds)
Drone-fpv-racer.com
$83.32

Propellers

HQProp Durable Duct-3 pour Cinewhoop (2x CW + 2xCCW)
Drone-fpv-racer.com
$3.48

FPV Camera

Caddx Vista HD System (11 builds)
Drone-fpv-racer.com
$191.79

Antenna

Antenne TrueRC Matchstick 5.8GHz Carbon Edition RP-SMA LONG - LHCP (1pc)
Drone-fpv-racer.com
$28.96

Receiver

TBS Crossfire Nano RX (SE) (349 builds)
Drone-fpv-racer.com
$39.43

Batteries

Batterie Lipo Tattu R-Line 6S 1050mAh 95C (4 builds)
Drone-fpv-racer.com
$36.04

Misc Parts

SMA to uFL/u.FL/IPX/IPEX RF Adapter Cable
Core-electronics.com.au
$8.91
Show stores (2)

Discussion

Sign in to comment

Waffles   Aug 14, 2020  
1

Mighty fine looking prints you got there, sir. What printer are you using?

M490fpv   Aug 14, 2020 
1

thank you very much!! i use ultimaker 2+ extended printer.

Waffles   Aug 14, 2020 
1

Oh man, OK now that's a printer! Those specs make my Dremel look like a fax machine... Thanks for the response, great builds!

sedwo   Aug 13, 2020  

Nice ESC motor wiring. I noticed we use the same T-Motor 1507-2700kv set. How hot do they run for you?

M490fpv   Aug 13, 2020 

thank you! 😊
unfortunately this baby was sold right when i finished it, so i don't have a long experience. i set up the same cinewhoop settings than in my kopis build, so it is really smooth. after 2 6s lipo test flight the motors were not hot. it flew nicely 😊

Guides & Reviews

59 4,669  47
30 days ago

For the longest time we've been limited to 3 to 4 minutes of flight and lots and lots of batteries. With more efficient motors and frame designs it's now possible to push the envelope much further. This guide will walk you through the process of building a micro long range quad capable of flying 8-30 minutes and more than 4km. The build is moderately difficult, but with the right tools and steady hands..

Read more
36 2,687  19
Jul 20, 2020

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more