By TheMrJahn on Jun 08, 2018

32  1,347  5

Project Venom based on AstroX - very strong and lightweigh frame. With new canopy it looks very good! RunCam Micro Eagle didn't fit becouse of big lens, had to adjust canopy by myself. T-Motor F60II Pro 2600kv are great! EMAX Avan Flow looks good on this build. Installed 3d printered TBS VTX mount, UNIFY PRO HV and Lumenier AXII Stubby antenna. Skitzo Bolt32 and Skitzo RevoltOSD finally arived, finished this build. LEDs are very bright and looks nice with "Larson scanner" option.

Flight and LEDs videos:

Replaced camera - installed new RunCam Micro Eagle Lumenier Edition (White)! Big thanks to Sergio from Pyro Drone (!!!! Best customer service worldwide - he helped me to get this cam! Looks awesome!

Upgraded motors - installed new T-Motor F80 Pro 1900kv and replaced 2000muf 25v capacitor for a two 1000muf 35v. Now this build fully support 6s batteries.


Part List


ASTRO X SWITCH (NO PDB) (6 builds)


Astro X Switch Nylon Canopy (2 builds)

Flight Controller

FlightOne SKITZO RevoltOSD Flight Controller (16 builds)

Flight Controller

RevoltOSD MillivoltOSD V2 (FL1 Logo) Cable Kit (2 builds)


FlightOne SKITZO Bolt32 50A 4-in-1 4-6s ESC (7 builds)


4 x T-MOTOR F80 PRO 1900KV 2200KV 2500KV 3-6S CW Thread FPV Racing Brushless Motor (2 builds)


EMAX Avan FLOW 5" Prop (6 builds)

FPV Camera

RunCam Micro Eagle With built in camera control (5 builds)

FPV Transmitter

TBS Unify Pro 5G8 HV (SMA) (586 builds)


Lumenier AXII Stubby 5.8GHz Antenna (RHCP) (230 builds)


Frsky XM+ Micro D16 SBUS Full Range Mini Receiver Up to 16CH for RC FPV Racing Drone (1422 builds)

Misc Parts

5Pcs CJMCU 4 Bit WS2812 5050 RGB LED Driver Development Board (3 builds)

Misc Parts

10Pairs/20pcs XT60 Plug Male Female Bullet Connectors For RC Drone Multirotor FPV Racing Battery (5 builds)

Misc Parts

Alarm Module w/ LED For NAZE32 F3 Flight Controller RC Drone FPV Racing Multi Rotor (11 builds)

Misc Parts

Matek 4 PCS 36*36mm FR4 Glass Fiber Board PCB Circuit Board 1mm Thickness (4 builds)

Misc Parts

1PC Realacc 45 Degree Antenna Adapter Connector SMA RP-SMA For RX5808 Fatshark Goggles RC Drone (11 builds)

Misc Parts

AstroX_TBS_VTX_mount by Kerush (3 builds)
See Site
Show stores (6)


Sign in to comment

JesusSquared   May 15, 2020  

Hey there, I just built a simillar quad using DJI. I feel like im not getting the most out of the F80 Pro 1900Kv motors though. I can only fit 5.1/x props on my quad so I'm literally running the highest pitch 5.1" props I can find. Are you running into a simllar issue? I feel like these could handle a 6" props easily.

TheMrJahn   May 16, 2020 

Hi, i prefer Emax AVAN Flow 5 Inch 5x4.3x3 for all my builds. They are best imho

AcidFPV   Jun 13, 2018  

This build is off the chain!! Awesome job. Would love to see those LEDs in motion.

TheMrJahn   Jun 15, 2018 

Will post some video next week!

TheMrJahn   Jul 09, 2018 

Guides & Reviews

27 1,299  11
18 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
43 4,846  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more