Frogflite

By danielkesler on Mar 11, 2018

13  800  4

Thanks to Drone Mesh.

The Matek BEC (MBEC2A) was used to power the VTX and camera.

Photos

Part List

Frame

TransTEC Frog Lite 218mm Carbon Fiber 4mm Arm X Frame DIY Frame Kit RC Drone FPV Racing Multi Rotor (41 builds)
Banggood.com
$29.99

Flight Controller

Racerstar StarF4S 30A Blheli_S Dshot 4 in 1 ESC AIO F4 OSD Flight Controller w/ BEC Current Sensor (18 builds)
Banggood.com
$56.99

Motors

4X Racerstar 2307 BR2307S Green Edition 2500KV 2-4S Brushless Motor For X220 250 300 RC Drone FPV Racing (2 builds)
Banggood.com
$39.99

Propellers

DAL 5x4.6 - 3 Blade, Green Cyclone Propeller - T5046C (Set of 4) (394 builds)
Getfpv.com
$2.40

FPV Camera

FOXEER Arrow V3 2.5mm 600TVL 4:3 HAD II CCD PAL/NTSC IR Block Mini FPV Camera Built-in OSD MIC (131 builds)
Banggood.com
$25.40

FPV Transmitter

E709TM3 5.8G 48CH 25mW 200mW 600mW Adjustable AV Transmitter w/ Mounting Hole for Flight Controller (5 builds)
Banggood.com
$15.50

Antenna

Realacc UXII 5.8G 1.6dBi RHCP/LHCP TX/RX FPV Antenna SMA/RP-SMA Male (19 builds)
Banggood.com
$6.99

Receiver

Flysky FS-A8S FS A8S V2 2.4G 8CH Mini Receiver with PPM i-BUS SBUS Output (91 builds)
Banggood.com
$9.99

Batteries

Infinity Graphene LiPo Battery 1300mAh 70C 4S 14.8V SY60 Compatible XT60 Support 15C Boosting Charge (7 builds)
Amazon.com
$23.99

Power Distribution

5V 12V Adjustable Voltage Dual BEC Output Board Only 1g for RC Drone FPV Racing (2 builds)
Banggood.com
$2.71

Misc Parts

Lantian WS2812B LED + 5V Active Buzzer for NAZE32 CC3D F3 F4 Flight Controller for RC Drone FPV Racing (6 builds)
Banggood.com
$3.61

Misc Parts

4 PCS 22XX Series Motor Silicone Anti-vibration Pad in for RC Drone FPV Racing Drone (11 builds)
Banggood.com
$2.12

Misc Parts

PARACORD PLANET Type III 7 Strand 550 Paracord
Amazon.com
$11.49
Show stores (3)

Discussion

Sign in to comment

Scott in Tokyo   Mar 12, 2018  

That is so frikkin adorable. No go pro?

danielkesler   Jun 03, 2018 

Here's what I used on the Dragonflight:

Aussieskibum   May 16, 2018  

I've been looking at those motors to try to get some spare parts flying on the cheap, what are your thoughts on them?

delta_fpv   Mar 12, 2018  

good stuff, all choices make financial sense (seems rare around here)

Guides & Reviews

29 1,579  11
26 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
45 5,038  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more