Kami 🔥⛩️🔥

By sergetania on Jun 09, 2018

4  300  2

Amazingly quiet and efficient drone. It gets 5 min of fly time on 650 mAh 2S batteries. Really good camera, well matched to 16:9 Dom V3 goggles.

The frame is nice but it's tight, not easy to squeeze all the components in.


Part List


Kamikaze 3" & 4" Race Frame Kit **New** (2 builds)
See Site

Flight Controller

Matek System 20x20mm F411-mini Mini F4 Flight Controller AIO OSD BEC and LED Strip for RC Drone (12 builds)


Spedix IS20A 20A 2-4S 20x20 M2 4in1 ESC - Replacement for IS100 Stack (43 builds)


4 x BrotherHobby Returner R3 1402 8100Kv Micro Motor (6 builds)


EMAX Avan Mini 3x2.4x3 Tri-Blade 3" Prop 12 Pack - Choose Your ColorRed (13 builds)

FPV Camera

Foxeer Monster V2 1.8mm 1200TVL 1/3 CMOS 16:9 PAL/NTSC IR Block FPV Camera w/ OSD and Audio (8 builds)

FPV Transmitter

AKK FX3 Ultimate Mini 20x20 25-600mW VTX w/ Smart Audio - MMCX & U.FLDefault Title (109 builds)


RDQ 5.8GHz Straight MMCX Dipole FPV Antenna - Linear (16 builds)


FrSky R-XSR 2.4GHz 16CH ACCST Micro Receiver w/ S-Bus & CPPM (823 builds)


FrSky X-Lite 2.4GHz Radio Controller (Red) (66 builds)


FatShark Dominator HDO FPV GogglesRechargeable 1800mah Pack (108 builds)

Misc Parts

Panasonic 1000uF 35V Low ESR Capacitor for ESC Noise Reduction (107 builds)

Misc Parts

RDQ 20x20 Mini Flight Controller Mount and Protector - FC Mount / Cover (3 builds)

Video Receiver

ImmersionRC rapidFIRE w/ Analog PLUS Goggle Receiver Module (129 builds)

Radio Module

Frsky R9M Lite - Radio Transmitter Module (Black) (11 builds)

Soldering Iron

Hakko FX888D-23BY Digital Soldering Station FX-888D FX-888 (blue & yellow) (24 builds)
Show stores (6)


Sign in to comment

le_vinsky   Aug 02, 2018  

Wow! 5 minutes on 2S with 3 inch props!? Impressive! Looks like these 1402's are crazy efficient.

sergetania   Aug 02, 2018 

Since then I have upgraded this quad to 1404 motors (4 min on 3S) and put the 1402s on 2.5" Ascent X. With the Ascent, I get 4-4.5 min of flight time. Go figure. Probably because the Ascent with 1402s is too much fun to fly!

Guides & Reviews

28 2,468  33
28 days ago

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more
26 6,964  24
Nov 30, 2019

In late 2019 DJI made inroads into the FPV scene with their remarkable low-latency digital system. It gave us a 720p video feed with latency on-par with the status quo, analog video. Traditionally we've used analog video systems for low-latency video, but the video quality is far from ideal. It's a trade-off we've been willing to accept for the control. Now we've got the best of both worlds and what..

Read more