MMD

By stevescene on Jun 19, 2018

3 463 8

MMD - More Massive Droner

Photos

Part List

Frame	MORE Massive Droner 3 inch (28 builds) Catalystmachineworks.com	$46.99
Flight Controller	OMNIBUS F4 Nano v5 with LC filter (3 builds) Store.myairbot.com	$29.99
ESCs	Ori32 4in1 ESC 4x25A 2020 (83 builds) Store.myairbot.com	$44.99
Motors	4 x Armattan Oomph TITAN MiNi 1407/3650 KV Motor (11 builds) Armattanquads.com	$59.00
Propellers	Lumenier 3x4x3 V2- Propeller (Set of 4 - Transparent Black) (15 builds) Getfpv.com	$2.24
FPV Camera	Caddx Turbo micro SDR1 2.1mm 1200TVL NTSC/PAL 16:9/4:3 Switchable Super WDR FPV Camera (3 builds) Taco-rc.com	$24.99
FPV Transmitter	PandaRC Mini5804 5.8G 48CH 0/25/100/200mW Switchable FPV Transmitter 20x20mm for RC Drone FPV Racing (13 builds) Banggood.com	$14.50
Receiver	TBS CROSSFIRE NANO RX (SE) - FPV LONG RANGE DRONE RECEIVER (412 builds) Team-blacksheep.com	$29.95
Batteries	AHTECH Infinity 4S 14.8V 550mAh 70C Lipo Battery with XT60 Plug Connector for RC FPV Racing Drone (5 builds) Banggood.com	$16.99

Show stores (7)

Like Copy Part List Follow stevescene

Discussion

sergetania Aug 10, 2018

Any problems pairing the ESC with the FC? I am doing a build with this stack and the motor 4 doesn't spin. No visible problems with the ESC, no shorts that I can find, the contacts between esc and fc are fine. Strangely, the motor mapping for m4 changed after BF update from 3.3.0 which was the original for the fc. Not sure it is the problem though. Thanks!

therock Jun 25, 2018

verye nice build, how did you fit the strap?

Show 3 more comments

stevescene Jun 26, 2018

If you are asking how the XT60 fit into the frame. The answer is, the XT60 width is shorter than the width between the 2 side carbon fiber plate. As for the bottom clearance, it depends on your stack. I am using the airbot ori32 4in1 ESC, the main power wires are soldered under the ESC, so, enough space between the ESC and the main carbon fiber board is necessary. In my case, I use 4 long M3 nylon screw to hold the stack in position, under the ESC, I have 4 x 3D Printed standoff, which is around 5 mm high. These provide enough space for the wire as well as the strap under the ESC board.

therock Jun 26, 2018

ah okay gotcha on that one, makes sense.. thanks and i really really like your build quality and design :)

stevescene Jun 26, 2018

i am glad you like it

Guides & Reviews

115 22,060 40

Build a 5" Long Range Drone - Transformer Ultralight

Jun 21, 2021

AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..

69 17,609 65

Build a DJI FPV Cinewhoop - QAV-CINE Freybott Edition

Mar 04, 2021

With the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..

Guides and Reviews