Another Bush Chook Rooster aka " GINSLIPS"

By Fisted on Aug 21, 2018

4  155  0

The long awaited build of my rooster has finally happened.
I call her "GINSLIPS" A dark theme, matt black with a splash of red inside

GIN - a trap or snare for game. / SLIPS - avoids the traps..

  • I am not using the original esc and flight controller i had planned, i will hold on to that to upgrade should the gear not hold up to the challenge.
  • super tight build with a pigtail mod to the vtx required .. the frame is definately made for a AIO flight controller, single ESCs and smaller reciever and VTX as I originally planned, also the reason for the upside down ESC
    -The Armattan slop stoppers where actually too tight and without some filing or cross threading screws they never would have fit, so i left them out.
    -I got my hands on some neat protective braided heat shrink that is like kevlar when heated and shrunk that will protect the motor wires from propstrike.
    -FPV cam and gopro mount custom coloured with a flexible coating.. that stuff is amazing on TPU
    -The JST connector for FC power in the photos was removed due to room restrictions, it was there for easy disconnection. Dont ask me why.

  • The FC is flashed with BF 3.2 and even though the Fortini is good for 32 khz and 8khz PID loop i will just run with 8 and 2 for now, and slowly up her to see how it goes with my eratic and some what damaged flying style
  • ESC is BLHeli-S , so Multishot it is.
  • all up weight with props, bat, gopro, etc is 673g

everybody seems to love thier Rooster and that certainly depends on the build, hopefully mine is one of those....


Part List


Armattan Rooster Frame Kit (133 builds)

Flight Controller

Furious FPV FORTINI F4 32Khz 16MB Flight Controller with OSD Rev.2 5V 2A BEC for RC Drone FPV Racing


Sunrise Cicada 35Ax4 35A Beheli_S BB2 2-4S 4 in 1 ESC Support Oneshot42 Multishot Dshot for RC Drone (4 builds)


T-motor F40 Pro II v2 2306 2400kv Mini Quad Motors (Single) (3 builds)


2 Pair DALPROP T5045C Cyclone 5 Inch 3 Blade Propeller Clover Prop Black Red Orange Green (199 builds)

FPV Camera

RunCam Eagle 2 Pro 16:9 4:3 Switchable 800TVL CMOS FPV Camera /w OSD & Audio EAGLE2PRO-OR (3 builds)

FPV Transmitter

Eachine TS5828L Micro 5.8G 600mW 40CH Mini FPV Transmitter with Digital Display For RC Drone (18 builds)


2pcs 50/85mm Pagoda 2 pagoda-2 5.8GHz FPV Antenna SMA&RP-SMA plug connector VS Foxeer Lollipop antenna for FPV RC Racing Drone


FrSky XSR 2.4GHz 16CH ACCST Receiver with S-Bus and CPPM


Tattu R-Line 1300mAh 95C 4S1P lipo battery pack


FrSky ACCST Taranis Q X7 2.4GHz 16CH Mode 2 Transmitter Blue Orange for RC FPV Racing Drone (218 builds)

HD Camera

Access Denied
See Site

Misc Parts

Snakeskin Mesh Wire Sleeve For Motor Cables Battery Lead (1 meter)

Misc Parts

Phaser3D Rooster/Chameleon TI GoPro Session/ Runcam 5 mount TPU (4 builds)

Misc Parts

stewart is creating Build, review and Flight videos on all things FPV related | Patreon
See Site
Show stores (7)


Sign in to comment

Guides & Reviews

28 1,340  11
19 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
43 4,878  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more