Gold Stinger

By Sasquads on Sep 21, 2018

19  347  0

Donald Trump asked me to build a quad for him.
So it turned out to this 6 inch lightweight with GPS.
He has not tried it yet, he's too busy slaying bando's at the time.
The Emax MT-2208 II are very efficient in combination with the Emax long range propellors. I got more than 6 minutes flight time in the testfilght as seen on the video.
GPS works fine, heading, distance, speed. Only have to test the return function.


Part List


Hantu'6 6 Inch 240mm Wheelbase 4mm Arm Carbon Fiber FPV Racing Frame Kit for RC Drone (2 builds)
See Site

Flight Controller

Betaflight F4 Flight Controller V3 +OSD+TF Slot FCB Updated for RC PRO FPV Indoor Racing Quadcopter Drone


4 x HGLRC BS28A BLHeli - S 28A ESC - $5.99 | (15 builds)


EMAX New MT2208 II 2000KV Brushless Motor Set - $77.02 |


2 Pairs Emax AVAN Long Range 6 Inch 6038 6X3.8X2 Propeller Black Color CW CCW for RC Drone (9 builds)

FPV Camera

Eachine SpeedyBee SEC 1/3 CCD 600TVL 2.3mm FOV 145 Degree Mini FPV Camera With OSD For RC Drone (4 builds)
See Site

FPV Transmitter

Eachine TX5258 5.8G 72CH 25/200/500/800mW Switchable FPV Transmitter Support OSD Configuring Smartaudio (10 builds)


Pagoda LHCP/RHCP 60mm 5.8G 2dBi FPV Antenna SMA/RP-SMA With Case Red/Purple FPV RC Drone (3 builds)


1.7g Fli14+14CH Mini Receiver Compatible Flysky AFHDS-2A w/ RSSI Output for FS-i6 FS-i10 Turnigy I6S (45 builds)

Power Distribution

Realacc RPDB Power Hub Power Distribution Board PDB 5V & 9V & 12V 3-8S BEC for RC Drone FPV Racing (3 builds)
See Site


Flysky FS-NV14 2.4G 14CH Nirvana Transmitter with iA8X Receiver 3.5 Inch Display Open Source (19 builds)

Misc Parts

HGLRC 7M/8M Ublox M8N GPS Module For APM Pixhawk CC3D Naze32 F3 Flight Control Controller For RC Camera Drone Accessories Accs

Misc Parts

16MM Wide 5/8" TIGHT Braided PET Expandable Sleeving Cable Wire Sheath 1 Meter

Misc Parts

Hantu 5" Racing Canopy by kah00na
See Site
Show stores (4)


Sign in to comment

Guides & Reviews

39 4,016  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more
28 7,815  38
Nov 30, 2019

In late 2019 DJI made inroads into the FPV scene with their remarkable low-latency digital system. It gave us a 720p video feed with latency on-par with the status quo, analog video. Traditionally we've used analog video systems for low-latency video, but the video quality is far from ideal. It's a trade-off we've been willing to accept for the control. Now we've got the best of both worlds and what..

Read more