Bando Basher 4"

By daich on Mar 28, 2019

11  840  2

this is an early revision of this frame. inprovements have already been made on the armattanproductions page.

dual camera mount is perfect for me. it also has a beefy bottom plate for ruggedness. a low stack height so the top mount battery sits close to the prop line. There is lots of space for the build with the option of two 20x20mm stacks or one 30x30mm
I had a spare 30x30 AIO fc and I also used the Foxeer Mix in its out of box 30x30mm form. Will swap out the lens to a gopro lens to avoid as much fisheye as possible.
Interested in how these cheap Tyro motors perform as well as the Mix.

--update 1st April 2019
tyro79 motors are surprisingly smooth. efficient due to the lower KV. the foxeer mix is terribly fisheyed. what is worse though is the oversharpening and low bitrate.
the cam plates have a bit of wobble and it shows up in the HD footage. this is a protoype frame so this already has been fixed in the latest revision.
i was pleasantly surprised how well my shorter 1300mah 4s packs sit in the top plate. I'll easily get 5 minutes of flight but hasnt been proven yet because of dogs :)

—20 May 2019


Part List


Bando ‘Basher’ 3”

Flight Controller

KISS CompactCTRL CC All-in-One (FC + 16A ESC x4)

Flight Controller

Racerstar StarF4S 30A Blheli_S Dshot 4 in 1 ESC AIO F4 OSD Flight Controller w/ BEC Current Sensor (17 builds)


4 x Eachine Tyro79 3 Inch DIY Version FPV Racing RC Drone Spare Part 1607 2800KV 2-4S Brushless Motor (4 builds)


HQ 4x4.3x3 V1S (2CW+2CCW) PC **Choose Color** (7 builds)

FPV Camera

RunCam Micro Eagle 800TVL 16:9/4:3 NTSC/PAL CMOS FPV Camera - Red (297 builds)

FPV Transmitter

TBS Unify EVO 5.8GHz Video Transmitter (13 builds)

FPV Transmitter

CA$19.11 Eachine VTX03 Super Mini 5.8G 72CH 0/25mW/50mw/200mW Switchable FPV Transmitter RC Parts from Toys Hobbies and Robo


Foxeer 2pcs FPV Antenna Lollipop 5.8G 2.5dBi Super Mini RHCP Antenna SMA Male for RC Drone FPV Quadcopeter Multicopter TX/RX (Bl (4 builds)


TBS Crossfire Nano RX - FPV Long Range Drone Receiver (568 builds)


Jumper T12 PLUS Open Source 16ch Radio with JP4-in-1 Multi-protocol RF Module With HALL Gimbal for RC Drone Car Boat (4 builds)


FatShark Dominator V2 Headset System Goggles Video Glasses 600 X 480 VGA
See Site

HD Camera

GoPro Hero5 Black — Waterproof Digital Action Camera for Travel with Touch Screen 4K HD Video 12MP Photos (4 builds)

Video Receiver

GTeng T909 5.8G FPV Artifact 32CH Receiver 2 inch LCD Wearable Watch for RC UAV Quadcopter Drone Aircraft -

Video Receiver

ImmersionRC rapidFIRE w/ Analog PLUS Goggle Receiver Module (129 builds)

Radio Module

TBS Crossfire Micro TX (102 builds)

Battery Charger

iSDT SC-620 Smart Charger (500W)
See Site

Soldering Iron

MINI TS100 Digital OLED Programmable Interface DC5525 Soldering Iron Station Built-in STM32 Chip (145 builds)


Upgraded MINI ES121 Electric Screwdriver Smart Repairtools Built-in STM32 Chip OLED with Screwbits (2 builds)


Turnigy Transmitter Bag / Carrying Case


SpeedyBee Bluetooth USB Adapter

Misc Supplies

FPV antennas for drones - Actuna TBS ImmersionRC - Actuna Sp. z o.o.

Misc Supplies

TrueRC X-AIR 5.8GHz Crosshair Antenna (RHCP) (4 builds)

Misc Supplies

Foxeer Lollipop 2 Stubby 5.8G Omni Antenna(2pcs)

Misc Supplies

ISDT BattGo BG-8S Smart Battery Checker Balancer Receiver Signal Tester Quick Charge Function (4 builds)
See Site
Show stores (13)


Sign in to comment

d'jazz.fpv   Apr 01, 2019  

So the 4" props goes well on the 3" frame ?

daich   Apr 01, 2019 

This a 4" basher frame...there is also a 3" version

Guides & Reviews

27 2,088  29
23 days ago

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more
25 6,829  24
Nov 30, 2019

In late 2019 DJI made inroads into the FPV scene with their remarkable low-latency digital system. It gave us a 720p video feed with latency on-par with the status quo, analog video. Traditionally we've used analog video systems for low-latency video, but the video quality is far from ideal. It's a trade-off we've been willing to accept for the control. Now we've got the best of both worlds and what..

Read more