Project 399 Super OG

By jpohl88 on May 15, 2019

19  910  10

Absolutely love this frame! super easy to build.

Photos

Part List

Frame

Super G (21 builds)
Project399.com
$75.00

Flight Controller

HyperLite F4 OSD V2 F4 Flight Controller with VTX Pit Mode (16 builds)
Getfpv.com
$32.99

ESCs

PYRO32F3-45Amp 4in1 F3 32bit BLHELI ESC 4x45A (10 builds)
Pyrodrone.com
$49.99

Motors

5 x TBS Ethix Mr Steele 2306 2345kv Silk V2 Motor (11 builds)
Getfpv.com
$109.95

Propellers

8 x HQ Prop ETHIX S5 5x4x3 Tri-Blade 5" Prop 4 Pack - Light Grey (79 builds)
Racedayquads.com
$27.92

Propellers

6 x HQ Prop ETHIX S3 5x3.1x3 Tri-Blade 5" Prop 4 Pack - WatermelonDefault Title (49 builds)
Racedayquads.com
$20.94

Propellers

JOHNNY FREESTYLE - SPECIAL LIMITED EDITION 5" FREESTYLE PROP (6 builds)
Pyrodrone.com
$3.29

FPV Camera

RunCam Micro Eagle Pro "Rotor Riot Joshua Bardwell Edition" 800TVL 16:9/4:3 NTSC/PAL CMOS FPV Camera - BlackDefault Title (24 builds)
Racedayquads.com
$46.95

FPV Camera

Runcam Swift Mini 2 Mr Steele Edition FPV Camera (2 builds)
Hobbyrc.co.uk
See Site

FPV Transmitter

TBS Unify EVO 5.8GHz Video Transmitter (18 builds)
Getfpv.com
$59.95

Antenna

2 x TBS Triumph Pro (SMA RHCP) Antenna (21 builds)
Pyrodrone.com
$39.90

Receiver

TBS Crossfire Nano Rx FPV Long Range Drone Receiver (1488 builds)
Pyrodrone.com
$24.95

Batteries

6 x Talon FAF Series 1300mAh 125C 18.5V 5S Lipo Battery with XT60 Connector
Heli-nation.com
$191.94

Goggles

Fat Shark Dominator HD3 Core Modular FPV Headset (87 builds)
Progressiverc.com
$399.99

Hardware

FPV Quad Hardware Kit Black Oxide
Teamknkhardware.com
$17.99

Misc Parts

Pyro Race LEDs 35mm (4 Pcs.) (10 builds)
Pyrodrone.com
$6.99

Misc Parts

Kyosho Zeal Vibration Absorption Gyro/Reciever Mounting Gel (1 Sheet)
Amainhobbies.com
$14.49

Misc Parts

PTT0.31BNY - Flexo® PET Tight Weave - 5/16" - Black / Neon Yellow - 10 ft cuts
Wirecare.com
See Site

Video Receiver

ImmersionRC rapidFIRE w/ Analog PLUS Goggle Receiver Module (179 builds)
Getfpv.com
$159.99

Battery Charger

ISDT Q6 Pro BattGo 300W 14A Battery Balance Charger (62 builds)
Racedayquads.com
$59.99

Soldering Iron

TS100 Soldering Iron (B2) (264 builds)
Team-blacksheep.com
$59.99

Tools

Moore Ideal Products 9512 Metric Speed Tip Set (4 builds)
Amazon.com
$34.69

Backpack

Think Tank PhotoFPV Session Backpack for Drones (3 builds)
Bhphotovideo.com
$94.45
Show stores (13)

Discussion

Sign in to comment

FrenchB   May 20, 2019  

Why’d you hide your LED racewires in the sheathing?

jpohl88   May 20, 2019 

Just going for a super clean look... You can see the LEDs bright as day coming through the mesh. Came out pretty badass

Jodie Froster   May 16, 2019  
1

What made you go for the "stash box" under the tail for your reciever?

jpohl88   May 16, 2019 

I didnt want to put it on the bottom side of the top plate and have the strap go around it or on top or below the Unify. I had just been to my local hobby shop where Blake (NubbFPV from DRL) is the quad tech and he designed that printed box for his Super G+ so he could run a massive bottom mount battery for Long Range without it wobbling all over the place. I asked him if he could make it hollow and thr rest is history. But i guess mostly because my OCD wouldn't allow me to mount it in a non-clean way.

Jodie Froster   May 16, 2019 

It clearly IS right below the unify.... perhaps you could get more distance between them, for less plastic weight with a different 3d printed part. I like it, and how clean it looks. It is a LOT of plastic, for not much distance though.

jpohl88   May 16, 2019 

Sorry I meant like literally sitting on top or bottom of the Unify (touching it). The carbon in between acts as a heat sink. I'm sure a different part could've been utilized but he already had that designed and it works well. As for weight, its a high KV 5s build so a couple grams isn't going to make or break.

Jaub   May 15, 2019  

How do you like the pyro 4in1?

jpohl88   May 15, 2019 

Love it so far. Buttery smooth and easy to build. The only "complaint" i have is the motor pads closest to the mounting gromets get coverwd ever so slightly by the grommets, no problems just a slight design flaw. Needs maybe two mm to clear but its really just and issue with my OCD haha

RZFPV   May 15, 2019  

do u have the stl files for the cap holder

jpohl88   May 15, 2019 

I don't. They were made custom by NubbFPV at my local Hobby Shop because I thought I had the 1000 size but they are the 680s so he had so shrink them a bit.

Guides & Reviews

Jun 21, 2021

AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..

Read more
Mar 04, 2021

With the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..

Read more