Super G Plus / Tree Surfer

By jseaber on May 17, 2019

19  1,315  5

The SuperG Plus is currently my favorite build! 7" props have a deep, stealthy sound, barely audible beyond 75 meters.

The SMA+GPS mount is a remix of FPV_vibe's design, edited to accommodate the 26mm long Matek SAM-M8Q GPS module. I also increased height of the SMA mount by 2mm to avoid pigtail collision with the lower deck.

Cruising flight time easily reaches 11+ minutes from a 5S/1800mAh pack, and 6+ minutes from 4S/1300mAh.


Part List


Super G Plus (19 builds)

Flight Controller

Matek F722-SE F7 30x30 Flight Controller w/ 5V BEC , Video Power Switcher, Dual Camera Image Switcher (36 builds)


4 x Spedix ES30 HV 3-6s BLHeli_S DShot600 30A ESCDefault Title (176 builds)


4 x MB Primo 2208 1750kv (3 builds)


HQProp DP 7X3.5X3 V1S PC Propeller (Set of 4 - Black) (13 builds)

FPV Camera

RunCam Micro Eagle - Lumenier Edition (White) (14 builds)

FPV Transmitter

RDQ Mach 3 Video Transmitter 25-1000mW VTX 2-6S - U.FL or MMCX (119 builds)


TBS Crossfire Immortal T V2 Antenna (13 builds)




TBS Crossfire Nano RX - FPV Long Range Drone Receiver (708 builds)


Tattu R-Line Version 2.0 15.2V 4S 1550mAh 100C LiHV Battery - XT60 (14 builds)


RDQ Series 18.5V 5S 2200mAh 80C Long Range LiPo Battery - XT60 (24 builds)


RDQ Series 18.5V 5S 1800mAh 100C LiPo Battery - XT60

3D Printed

Super G Plus - SMA and 26mm long GPS Mount by threedonuts
See Site

3D Printed

AirBlade Immortal T Antenna Mount by airbladeuav
See Site

3D Printed

Super G GoPro Mounts by urbankuest
See Site


M5 Low Profile Motor Nut w/ Flange (1PC) - Choose Your Color (3 builds)

Misc Parts

Ummagawd UMMAGRIP Universal Super Sticky Battery Pad (131 builds)

Misc Parts

HellGate FPV Buzzer - Automatic Alarm w/ Internal BatteryDefault Title (6 builds)

Misc Parts

Matek SAM-M8Q GPS Module (6 builds)
Show stores (6)


Sign in to comment

cjdavies   Jun 26, 2019  

Could you share a link to the STL for the 900MHz dipole mount?

jseaber   Jun 26, 2019 

The Immortal T holder shown above was actually half of a broken print found here:

I've since moved to this two part design:

dillionverma   Aug 27, 2019 

What's wrong with the first immortal T + vtx holder you listed?

jseaber   Aug 28, 2019 

The pictured holder broke right after printing, so the VTX mount portion was destroyed. The antenna mount was not very stable.

Long story short, this quad is at the bottom of a lake :-(. I rebuilt with Airblade's ballmount Immortal T holder:

MATEKMAN   May 20, 2019  

perfect long range build !

Guides & Reviews

29 1,565  11
25 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
44 5,031  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more