Hello,
Look at this picture : http://img.banggood.com/thumb/water/oaupload/banggood/images/A3/F5/8ff91e5c-9369-4f52-88f7-969cc8539492.png
If you're using a FS-A8S, you need to connect the white wire to RX3, the red one to +5V and the black one to GND in the top left.
Tell me if you have any other questions (on how to setup cleanflight (or betaflight) for the evolution for example)

Cheers

thank you so much, im very lost at this point, i ll try it right now

Thanks for saving me many hours of frustration since I borrowed your tips for the FS-A8S and my micro flight controller. I have a quick question. I haven't been able to figure out why this needs to be connected to UART3 and not say, UART2. I haven't been able to find anything that states otherwise. UART is just a communication port from what I know and I should be able to use any one that isn't used, correct?

Hello Chalky,
As far as I know, you should be able to connect it to UART2 indeed. I didn't know much about anything when I built this so I just followed along a video I found at the time...
I just received new micro receivers which I will test shortly (the RX2A-Pro) hopefully it performs well.

Sure !
If I remember correctly, what you need to do in BetaFlight is :
In Ports, activate Serial RX on UART 3
In Configuration, set receiver mode to Serial-based receiver and Serial Receiver Provider to IBUS
In Receiver, set Channel Map to AETR1234

Don't forget to set the Output mode to i-BUS on the Turnigy Evolution.

Tell me if that covers it :)

Cheers

Benn

YEEEEEAHHHHH FINALY!!!!, AFTER 3 MONTHS OF DESPERATION AND FRUSTRATION.

THANK YOU SO MUCH!!!

but now the aux 1 dont moves, only the aux 2 and 3 do it, thats normal or not? apart from that everithing goes good

You're very welcome ! :)
That might be linked to the flight mode thing on the new evolution firmware. Try deactivating it to make sure, and if that solves it, you can always turn it on again later and really understand how it works. I don't have my evolution with me right now but tell me if you want me to look into it.
Are you going to publish your build? I'm curious to know what you went for ☺

My build is almost the same as yours, but with diferent camera and batteries, i modified the battery conector to use the tipical tiny whoop battery, i also have the props a bit diferent, a 3 blade props, but i m so rookie so i didt feel anything diferen from 4 blade props. i update more photos at the top with the drone finished. And yes, the problem with the aux is caused by the new flight mode in the updated firmware of the turnigy evolution.

Glad you found the source of the Aux 1 issue. Basically, once configured properly, flight mode doesn't change the way Betaflight receives the information, but it allows you to have the information of what mode you're in on the Evolution's screen, which can be nice :)

I highly recommend switching to a Furibee F36 as a base for this build (I have to publish the new build). It has way more power to carry the FPV gear.
I also ordered an E011 which I will try as soon as it gets in. I have high hopes.
Finally, I saw that Eachine finally made an F3 FC with AFHDS 2A receiver included ! (also ordered, i'll probably put that on the E011 frame).
https://www.banggood.com/Beecore-F3_EVO_Brushed-ACRO-Flight-Control-Board-DSM2-For-Inductrix-Tiny-Whoop-Eachine-E010-p-1089021.html

Cheers

ye, i saw that f3 fc today too, maybe i do other tiny whoop, but with other build and with a canopy:

motors: https://www.banggood.com/4X-Racerstar-615-6x15mm-67000RPM-Coreless-Motor-for-Eachine-E010-E010S-Blade-Inductrix-Tiny-Whoop-p-1141773.html?rmmds=mywishlist
props: https://www.banggood.com/10PCS-Kingkong-31mm-Propellers-Sets-for-Tiny6-Tiny-Whoop-Eachine-E010-E010C-E010S-Blade-Inductrix-p-1141695.html?rmmds=mywishlist
fc: https://www.banggood.com/Beecore-F3_EVO_Brushed-ACRO-Flight-Control-Board-DSM2-For-Inductrix-Tiny-Whoop-Eachine-E010-p-1089021.html?rmmds=mywishlist
camera: https://www.banggood.com/Eachine-Fatbee-FB90-Micro-Racing-Quadcopter-Spare-Parts-5_8g-25MW-48CH-VTX-520TVL-CMOS-14-Camera-p-1108072.html?rmmds=mywishlist
camera mount: https://www.banggood.com/Eachine-Turbine-QX70-Micro-FPV-Racing-Quadcopter-Spare-Parts-Camera-Fixing-Mount-QX703-p-1108078.html?rmmds=mywishlist
frame: https://www.banggood.com/Eachine-E010S-E010C-E010-Micro-FPV-RC-Quadcopter-Spare-Parts-Frame-Kit-p-1126510.html?rmmds=mywishlist
batteries: https://www.banggood.com/5PCS-Charsoon-3_7V-250mAh-1S-30C60C-Lipo-Battery-for-Blade-Nano-QX-CPX-and-Tiny-Whoop-p-1124144.html?rmmds=mywishlist

but before this, i ll buy a wizard (i want to taste freeride in a racing drone) :-)

have a nice day

Hello,
No serious issue on my end, but I'm using cleanflight.
Flashing a new version of it was a bit tricky though. Basically, I used zadig to install the drivers, unplugged the board, then, used the gui to download the firmware and finally, plugged in the board and flashed the firmware.
Concerning BF, have you looked at this :

Concerning the A8S, I'm using the X6B with my kiss build (https://rotorbuilds.com/build/1738) unfortunately so can't really help you there.
Tell me if I can help with anything else.

Benn