Anticrime v3 3" HD Cruiser

By Petefpv on Feb 28, 2020

9  277  1

Finally my first build is ready. It is sub 250g HD cruiser. Frame is Anticrime v3 "3 by @dialeksi.

Photos

Part List

Frame

Anticrime V3 - 3" LR HD quad by DiAleksi (3 builds)
Shop.brickracing.com
$32.90

Flight Controller

OMNIBUS AIO F4 V6 Flight Control - 5xUARTs (24 builds)
Store.myairbot.com
$34.99

ESCs

Airbot Ori32 BLHeli32 25A 4-in-1 ESC (82 builds)
Getfpv.com
$44.99

Motors

4 x EMAX RS1106 II 4500KV Micro Brushless Motor (28 builds)
Getfpv.com
$51.96

Propellers

6 Pairs Emax AVAN Mini 3 Inch 3X2.4X3 3-blade RC Drone FPV Racing Propeller CW CCW (56 builds)
Banggood.com
$5.77

FPV Camera

RunCam Split Mini 2 FOV 130 Degree 1080P/60fps HD Recording & WDR FPV Camera NTSC/PAL Switchable (86 builds)
Banggood.com
$69.99

FPV Transmitter

TBS UNIFY PRO 5G8 HV - RACE 2 (MMCX) (26 builds)
Pyrodrone.com
$29.95

Antenna

EMAX Nano 50mm 5.8G 3dBi FPV Antenna RHCP/LHCP SMA/MMCX/MMCX Angle for FPV Racing Drone (2 builds)
Banggood.com
$5.56

Receiver

FrSky R-XSR Ultra Mini Redundancy Receiver (847 builds)
Horusrc.com
$19.89

Batteries

Turnigy nano-tech 850mAh 4S 45~90C Lipo Pack (4 builds)
Hobbyking.com
$14.88

Radio

FrSky Taranis X-Lite Pro ACCESS 2.4GHz Radio Controller (Deep Sea Blue) (13 builds)
Getfpv.com
$199.99

Misc Parts

HGLRC Super Mini 1.38g WS2812 Colorful LED w/ 5V Active Alarm Buzzer Support Cleanflight Betaflight (19 builds)
Banggood.com
$3.24

Battery Charger

ISDT Q6 Pro BattGo 300W 14A Battery Balance Charger (41 builds)
Getfpv.com
$59.99

Soldering Iron

MINI TS100 Digital OLED Programable Interface DC5525 Soldering Iron Station Built-in STM32 Chip (161 builds)
Banggood.com
$49.99
Show stores (7)

Discussion

Sign in to comment

Jodie Froster   Feb 29, 2020  

What a cool 3" frame! I love the recessed screw holes in the top plate to hang the HD recording board without scratchin holes in your pack!

Guides & Reviews

39 4,016  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more
28 7,818  38
Nov 30, 2019

In late 2019 DJI made inroads into the FPV scene with their remarkable low-latency digital system. It gave us a 720p video feed with latency on-par with the status quo, analog video. Traditionally we've used analog video systems for low-latency video, but the video quality is far from ideal. It's a trade-off we've been willing to accept for the control. Now we've got the best of both worlds and what..

Read more