Chameleon Ti Mr

By Croox on Jul 06, 2020

8  339  1

Alright got another Armattan build for you guys. Started with a Chameleon Ti LR 7 inch frame which can be hard to come by these days, put a really nice sticker pack on it from Stickitskins which turned out great! My main goal with this quad is more of a Mid-range build (hence the TI-MR), still have TBS GPS for a RTH failsafe and a RX4R which claims a 40% operating range increase compared to other X series receivers. Also added the TBS Unify pro V3 for that juicy 800mW. The fpv camera is a Foxeer Monster mini with a 1.8mm lens at 1200TVL resolution with a 16:9 aspect ratio, I did have a hard time mounting this camera as the frame is designed for a 28.5mm camera, and the lens does poke out from the cage which is not ideal in case of a crash. As for the power-train I went with Pyrodrone F4 with the Pyrodrone 4 in 1 45amp V2(and a clear XT-60). For the props I elected the HQ 7x4x3 and for le pièce de résistance, the iFlight XING X2806.5 1800kv FPV Next-Gen Motor which I must say is the smoothest motor I have yet to use. They were a bit pricey at $32 per motor but do not plan on doing proximity or freestyle with this rig so they should(should) be good for a bit. The frame Is well thought out and allows for a very clean build. weight comes in at 504.6g and 766.8g with a CNHL 2200mAh 70c. This could also handle 6s if I wanted to but love how linear it is with the 4s as it just feels so locked and buttery. Be sure to follow my page if you like the builds as will be posting more soon!


Part List


Armattan Chameleon TI LR 7" Long Range Frame (7 builds)

Flight Controller

PYRODRONE F4 RACE with VTX PIT mode (6 builds)


PYRO32F3-45AMP "V2" 4IN1 F3 32BIT BLHELI ESC 4X45A (11 builds)


4 x XING X2806.5 FPV NextGen Motor


HQProp DP 7X4X3 Propeller (Set of 4 - Light Grey) (29 builds)

FPV Camera

Foxeer Monster Mini Pro - Red

FPV Transmitter

TBS Unify Pro 5G8 V3 (SMA) (172 builds)


IBCrazy 5.8 GHz Cyclone Antenna Set (RHCP)


FrSky RX4R 4/16 Channel PWM/SBUS 2.4GHz Receiver w/ Pins


CNHL G+PLUS 2200mAh 14.8V 4S 70C Lipo Battery


TBS M8 GPS Glonass (15 builds)

Misc Parts

Armattan Chameleon TI (3 builds)
Show stores (7)


Sign in to comment

butcher51   Jul 07, 2020  

I love these motors, soo smooth. Try it with 2 blade props, they sounds amazing :D

Guides & Reviews

29 1,573  11
26 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
44 5,035  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more