A new OSD has been introduced for KISS firmware users (FETtec OSD). I am currently in the process of building an Armattan Marmotte and waiting on the FETtec 45Amp ESC. A few individuals has asked about a wiring diagram for the FETtec OSD so I have put this together to help others in how to wire up their quads with the new OSD and 4in1 ESC with a KISS V2. My Rotorbuilds site has Wiring diagrams for the builds also. So take a look, hope you enjoy.
Key Fetures:
STM32 F7 processor (216mhz)
MPU-6000 Gyro
DSHOT 2400, OneShot
CRSF Shot
Full Feature FETtec OSD
FETtec 45amp ESC
FETtec Onewire
1000+ mW output VTX with mic
1/2 inch CMOS sensor for night flying
GPS with flash memory (BN-220) and RTH
Programable LEDS
Self Powered Buzzer with visual repeater
Total regulated 5v output power 2500mA
Flight Controller |
KISS FC V2 - 32bit Flight Controller
(62 builds)
Flyduino.net
|
$65.96 |
ESCs |
FETtec 4in1 ESC 45A
(25 builds)
Fettec.net
|
$69.90 |
FPV Camera |
RunCam Phoenix 2 1/2 CMOS 1000TVL 2.1mm M12 Lens FOV 155 Degree 4:3/16:9 PAL/NTSC Switchable FPV Camera
(47 builds)
Pyrodrone.com
|
$29.99 |
FPV Transmitter |
TBS UNIFY PRO32 HV (MMCX)
(119 builds)
Pyrodrone.com
|
$49.95 |
Antenna |
Lumenier AXII 2 5.8GHz Long Range SMA Antenna - RHCP or LHCP
(53 builds)
Racedayquads.com
|
$19.99 |
Receiver |
TBS Crossfire Nano Receiver (SE)
(1499 builds)
Defiancerc.com
|
$29.95 |
Misc Parts |
FETtec Spike Absorber
Defiancerc.com
|
$7.99 |
Misc Parts |
Beitian Dual BN-220 GPS GLONASS Antenna Module TTL Level RC Drone Airplane
(68 builds)
Banggood.com
|
$18.99 |
Misc Parts |
ViFly Finder 2 Buzzer - Lost Drone Finder/Locater/Alarm
(174 builds)
Racedayquads.com
|
$14.99 |
Misc Parts |
Panasonic EEU-FR1H471 Electrolytic capacitor Radial lead 5 mm 470 µF 50 V 20 % (Ø) 12.5 mm 1 pc(s) | Conrad.com
Conrad.com
|
See Site |
Thanks for the diagram. Just used it today on a build and worked like a charm. Just a small note/correction: if you connect the Ground wire from the OSD to the Serial 1 port when you have a GPS module connected or selected in Serial config, OSD will not work properly. Some times it will boot sometimes it won't. You only need to have one ground, the one directly from the FC or the VTX, both for some reason causes problems. Maybe some ground loop issue. Tested on two different rigs. Cheers!
AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..
Read moreWith the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..
Read more
Hello, where should I mount the fettec spike absorber with the capacitor? What awg size should I use to mount them? Thank you so much!