Beast Racing Drone

By TheMrJahn on Mar 08, 2017

25  959  3

Custom Racing Build - SpaceOne Formula 220X Racer, RunCam OWL PLUS, TBS PowerCube Elite Bundle (BetaFlight 3.1.7), TBS BulletProof 25A (BLHeli-S Rev16.65), T-Motor F60 2207 2450kv. Changed props from DAL 5040 3Blade to DYS 5045 3Blade Bullnose! Much faster and sounds perfect! Most appropriate batteries for such "hungry" build - Tattu R-Line 1550mah 4s 95c.
Update - installed new heavy props - EMAX T5050BN.

BetaFlight 3.1.7 PIDs for this setup:

set anti_gravity_thresh = 350
set anti_gravity_gain = 3.000
set p_pitch = 63
set i_pitch = 37
set d_pitch = 25
set p_roll = 48
set i_roll = 32
set d_roll = 22
set p_yaw = 83
set i_yaw = 32
set d_yaw = 20
set rc_rate = 100
set rc_rate_yaw = 100
set roll_srate = 82
set pitch_srate = 82
set yaw_srate = 80


Part List


Limited Time Offer - Formula 220X Racer (33 builds)

Flight Controller

TBS PowerCube Elite Bundle (6 builds)


4 x TBS BulletProof 25A DSHOT600 ESC BLOWOUT (31 builds)


4 x F60 2450 Kv (1pc)


10 Pairs Emax T5050 5050 5x5 BN Propeller CW CCW Red/Yellow/Orange/Green/Blue/Purple for RC Drone FPV Racing (8 builds)


2 x 2 Pairs DALPROP 5040 T5040 3 Blade V2 PC Propeller CW CCW For QAV250 ZMR250 240 RC Multirotors


2 x DYS 3-Blade 5045 5x4.5 Bullnose Propeller CW CCW 1 Pair for 200 210 250 280 Frame

FPV Camera

RunCam OWL PLUS 700TVL 0.0001 LUX FPV Camera FOV 150° Wide Angle F2.0 lens IR Blocked 5-22V (21 builds)


TBS Triumph SMA (RHCP 2pcs) (542 builds)


FRSKY XM+ Plus 16CH RECEIVER (1429 builds)

Misc Parts

TBS Powercube Cable Set

Misc Parts

90pcs M3 Stainless Steel Hex Socket Head Cap Screw 4/6/8/12/16/20mm Length (3 builds)

Misc Parts

Pyro-Drone Battery Strap 4 Pcs. / Pack (16mm x 250mm) (2 builds)

Misc Parts

10 PCS M3*35 Colorful M3 Aluminum Column Spacer for RC Racer Drone Multirotor Silver Black Red Orang (4 builds)

Misc Parts

5V WS2812B 43W 144 SMD 5050 RGB LED Strip Waterproof IP65 Individual Addressable (5 builds)

Misc Parts

AMASS XT60+ Plug Connector 14AWG 10cm Power Cable Wire (3 builds)

Misc Parts

Suleve™ M3NH3 6mm M3 Nylon Screw Black Hex Screw Nut Nylon PCB Standoff Assortment Kit 25pcs (7 builds)

Misc Parts

Insulation Layer (36mm x 36mm x 1mm)

Misc Parts

1PC Realacc 45 Degree Antenna Adapter Connector SMA RP-SMA For RX5808 Fatshark Goggles RC Drone (11 builds)
Show stores (5)


Sign in to comment

That Noob_Builder   Aug 13, 2018  

how has that frame been treating you well and have you had any problems with delamination problems in general or broken anything I was just asking since I'm planning to buy one of those frames and I'm not sure to buy the Spaceone fpv formula 220x racer.

TheMrJahn   Aug 14, 2018 

This frame is very strong - i haven't any problems with it. Good frame!

That Noob_Builder   Aug 14, 2018 

Alright thanks I'm gonna take your words and buy myself one of these frames

Guides & Reviews

53 4,027  44
25 days ago

For the longest time we've been limited to 3 to 4 minutes of flight and lots and lots of batteries. With more efficient motors and frame designs it's now possible to push the envelope much further. This guide will walk you through the process of building a micro long range quad capable of flying 8-30 minutes and more than 4km. The build is moderately difficult, but with the right tools and steady hands..

Read more
35 2,613  18
Jul 20, 2020

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more