The digital version of the Gravity One is taller and the solder pads for tx1 and rx1 are not the easiest. 1mm circular pads. That said if you do complete a build and it flies you will realize that this pretty light as far a 3 inch digital builds go. The flight controller is built for this frame and has non conventional pad placement. I 3d print my own TPU rubber bands for battery straps. Ahh, thanks to new sequre soldering iron I was able to get the OSD bridge with the frame on. Thank you Flyerbeyer! Jusat had a small experience with another quad and I think I am about done with latency. Putting this and all DJI bearing quads up on the bay for toomorrow night.
Frame |
FETtec Gravity 1 3" Frame (FG1)
Defiancerc.com
|
$39.99 |
Flight Controller |
FETtec Mini KISS AIO 15A
(2 builds)
Defiancerc.com
|
$68.99 |
Motors |
4 x FETtec 1303.6 5555KV Motors
Defiancerc.com
|
$71.96 |
Propellers |
DAL New Cyclone T3018 Tri-Blade 3" Prop 8 Pack - Crystal Red
Racedayquads.com
|
$2.99 |
FPV Transmitter |
Caddx Drone Parts for - Shop Caddx Drone Components
(2 builds)
Racedayquads.com
|
$168.99 |
Antenna |
BETAFPV 2pcs AIR Digital VTX Antenna 5.8G LHCP Drone Antenna 2.2DBi IPEX for HD Digital VTX Brushless Drone Like Beta75X Beta85X
Amazon.com
|
$18.99 |
Receiver |
Flywoo ELRS EL24P 2.4GHz Micro Receiver
Racedayquads.com
|
$15.99 |
Batteries |
GNB 550mAh 90C/180C 1S-6S LiPo Battery
(14 builds)
Fpvcycle.com
|
$15.99 |
AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..
Read moreWith the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..
Read more
I'm also building a HD Fettec Mini AIO. I use a Air unit and wonder how to set-up the OSD. You did'nt bridge the OSD. Is your OSD working as should?
I absolutely forgot to solder that. Nope, I have no OSD. Flying by feel until I get that motivated. That one is the hardest solder in my opinion due to the height of the adjacent components. Takes rehearsing. I grabbed a sequre iron and the one with the wand. It rocks as wand is thin. In the past I remember the OSD is worth playing with as far as position in Kiss. I think I settled on left for position. I just moved the advanced serial settings to DJI on uart1 the rest auto changed. Felix answered my inquiry I sent to Fettec on how to best solder and he advised put the DJI power right on battery pad. Route negative through any neg pad on the board.