2" Cutie

By jwangdk on Aug 24, 2017

0  662  5

Cute little 1103-based micro quad.

It's a tight frame for sure, but everything is well protected and not too messy.
The frame supports up to 3" props and is 3mm thick. 8000 kv motors. 66g dry.

I'm flying it with a firmware-upgraded Devo 7e on dsmx.


Part List


X3 EYAS 112mm Wheelbase 3mm/4mm Thickness Carbon Fiber FPV Racing Frame (5 builds)

Flight Controller

Kingkong 20*20mm F3 Flight Controller with 4in1 BLheliS 10A ESC 2-3S (8 builds)


4 x Racerstar Racing Edition 1103 BR1103B 8000KV 10000KV 1-3S Brushless Motor Red For 50 80 100 Frame (4 builds)


10 Pairs Racerstar 2035 50mm 4 Blade ABS Propeller 1.5mm Mounting Hole For 80-110 FPV Racing Frame (7 builds)


8 Pair DYS 2030 1.5mm Hole 2 Inch 3 Blade Propeller Triblade Bullnose Prop For 1102 1104 1105 Motor (18 builds)


2 x 10 Pairs Racerstar 2030 R-BN55X3 55mm 3 Blade Propeller Bullnose 1.5mm Hole For 1103-1106 Motor (3 builds)

FPV Camera

600TVL 1.8mm 1/4 CMOS 120 Degree Wide Angle Lens FPV Camera PAL/NTSC 3.7-5V for RC Drone FPV Racing (20 builds)

FPV Transmitter

Eachine VTX03 Super Mini 5.8G 72CH 0/25mW/50mw/200mW Switchable FPV Transmitter (426 builds)


3 x Gaoneng GNB 7.4V 350mAh 2S 80/160C Lipo Battery White Plug for RC Model (2 builds)


FrSky ACCST Taranis Q X7 Transmitter 2.4G 16CH Mode 2 White Black International Version for RC Drone (218 builds)


Skyzone SKY02S V+ 3D 5.8G 48CH FPV Goggles With Head Tracking HD Port DVR Playback for RC Drone (22 builds)

HD Camera

GoPro Session (59 builds)

Misc Parts

Walkera Devo 7E 7CH Transmitter Mode 2 Without Receiver (3 builds)
Show stores (2)


Sign in to comment

mattidallama   Sep 01, 2017  

How did you fit the vtx03 I have the same frame and I can't get the vtx03 to fit anywhere and it driving me crazy

jwangdk   Sep 03, 2017 

It's on top of the flight controller. Sandwiched between two thin rubberpads and held down with a rubber band.

mattidallama   Oct 12, 2017 

btw i had the 80mm version upgraded to there was so much more room thanks again for the help

Roto_RunnerFPV   Aug 24, 2017  

looks awesome, any flight footage?

jwangdk   Aug 25, 2017 

Thanks. Nope. Haven't got the gear for recording. I've flown it for half a battery.

Guides & Reviews

29 1,577  11
26 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
45 5,038  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more