Mockup

Gundelo

By Gundeltraud on Sep 14, 2017

2  22  0

Hallo Werner

Part List

Frame

Realacc X4R X5R X6R 180mm 220mm 250mm 4mm Arm Carbon Fiber Frame Kit with BEC Output PDB (12 builds)
Banggood.com
$23.46

Flight Controller

30.5x30.5mm Betaflight Omnibus F4 Pro V3 Flight Controller Built-in OSD Barometer SD Blackbox (61 builds)
Banggood.com
$25.49

ESCs

4X Racerstar RS30A V2 30A Blheli_S ESC OPTO 2-4S Support Oneshot42 Multishot 16.5 Dshot600 for RC Drone (89 builds)
Banggood.com
$53.57

Motors

4X Racerstar Racing Edition 2205 BR2205 2300KV 2-4S Brushless Motor Purple For 210 X220 RC Drone FPV Racing (10 builds)
Banggood.com
$33.71

Propellers

2 x CA$9.99 10% 10 Pairs Kingkong / LDARC 5040 5x4x3 3-Blade Single Color CW CCW Propellers for Racing Drone RC Parts from Toys (79 builds)
Banggood.com
$14.60

FPV Camera

Orange 1200TVL CMOS 2.5mm/2.8mm 130/120 Degree 16:9 Mini FPV Camera--pal/NTSC 5V-12V For RC Drone
Banggood.com
$10.39

FPV Transmitter

Eachine TX526 5.8G 40CH 25MW/200MW/600MW Switchable AV Wireless FPV Transmitter RP-SMA Female (122 builds)
Banggood.com
$14.92

Antenna

2 x Realacc Pagoda RHCP Antenna 65mm 5.8G 5dBi Panel Plate Omni Directional FPV Short Antenna RC Drone (23 builds)
Banggood.com
$8.66

Receiver

FrSky XSR 2.4GHz 16CH ACCST Receiver Board S-Bus CPPM Output Support X9D X9E X9DP X12S X Series (480 builds)
Banggood.com
$15.99

Batteries

2 x Turnigy Graphene 1300mAh 4S 65C Lipo-Pack w / XT60
Hobbyking.com
$43.98

Misc Parts

Eachine EV800 5 Inches 800x480 FPV Goggles 5.8G 40CH Raceband Auto-Searching Build In Battery (23 builds)
Banggood.com
$54.59

Misc Parts

Neu! IMax B6AC 50W RC LiPo charger Ladegerät Batterie Balance Charger DHL
Ebay.com
$24.69
Show stores (3)

Discussion

Sign in to comment

Guides & Reviews

28 1,450  11
22 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
44 4,945  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more