Armattan Rooster 5" Bling build
Frame |
Rooster
(140 builds)
Armattanquads.com
|
$99.75 |
Flight Controller |
CL Racing F4S Flight Controller
(18 builds)
Armattanquads.com
|
$67.00 |
ESCs |
Spedix GS35 BLHeli32 4in1 ESC - FPV FlightClub
Fpv-flightclub.com
|
$54.00 |
Motors |
4 x Cobra Champion Series 2207 CP2207 2300KV 2450KV 3-6S Brushless Motor For 250 280 RC Drone FPV Racing
(8 builds)
Banggood.com
|
$91.96 |
Propellers |
HQProp 5x4.8x3 V1S Propellers
(76 builds)
Fpvheadquarters.com
|
$3.60 |
FPV Camera |
RunCam Eagle 2 Pro Global WDR OSD Audio 800TVL CMOS FOV 170 Degree 16:9/4:3 Switchable FPV Camera
(43 builds)
Banggood.com
|
$51.90 |
FPV Transmitter |
TBS Unify Pro 5G8 HV (SMA)
(596 builds)
Team-blacksheep.com
|
$49.95 |
Antenna |
Lumenier AXII Stubby 5.8GHz Antenna (RHCP)
(2 builds)
Amazon.com
|
$19.99 |
Receiver |
FrSky R-XSR Ultra SBUS/CPPM D16 16CH Mini Redundancy Receiver 1.5g for RC Multirotor FPV Racing Drone
(937 builds)
Banggood.com
|
$24.29 |
HD Camera |
GoPro HERO5 Session
(303 builds)
Getfpv.com
|
$199.99 |
Beautiful build! Which width of wire mesh did you use for the motor wires? They look like they're fabric and not plastic.
What a fantastic build. I'm about to build one almost exactly the same. I have a couple of questions if you don't mind ;-)
Thank you for the feedback!
Lowest is 30 degrees.
Where did you solder the TBS Unify onto the Spedix. Do you have a picture? I'm guessing you wouldn't have the battery leads, capacitor and TBS all on the same +- pads?
Did you have to extend your motor wires?
Regards,
Thanks so much for response. Is your FC getting its power source only from the JST wires from the Spedix? I was wanting to use the VBAT pads on my FC but I'm thinking the JST wires are so thin and probably wouldn't carry the full VBAT power to the FC? Also, do you know why the Spedix JST connection has 2x positive and 2x negative leads? I thought one of each would be enough.
Yep, I've used the jst on the spedix to power the FC, and I've used as well its current sensor so I did bridged one of the joints to prefer an external current sensor instead of the internal from CLRacing F4s. The other +/- from spedix you can use on powering your VTX HV (optional). Good luck on your build, send me a link once you've uploaded it here. Thanks!
Hi, how did you fit the runcam eagle? Mine is too wide.
I had to sand off 0.5mm from the sides.
Yes I have the metal casing.
I had to sand off a bit on the sides to make it fit. As you can see in my build... https://rotorbuilds.com/build/10613
Cheers
Does the AXII antenna suffer from being so near to the frame? have you tried with a non-stubby version?
AirbladeUAV has done it again and this time they've brought long range to the 5" class! Based on the popular Transformer Mini, the new Transformer 5" Ultralight adopts a lot of the same design philosophies with larger props and more payload capacity. It can fly upwards of 20 minutes on a 4 cell Li-Ion battery pack and in ideal conditions it's got a range of over 4 to 5 miles. In this guide I'll walk..
Read moreWith the release of the DJI FPV Drone cinematic FPV has become a lot more accessible, but you certainly don't want to crash a $750 drone! The QAV-CINE Freybott is a compact, lightweight cinematic FPV drone that can take a hit and keep going. It's a lot safer to fly indoors and around people. With a naked GoPro or the SMO 4k you can capture some great stabilized footage. In this guide I'll show you..
Read more
beautifully put together. it inspired me to build one for my brother as an xmas present