Jyuichi-go Microblivion II 3"

By irmanhilmi on Aug 15, 2019

13 5 2

Basically a transplate of https://rotorbuilds.com/build/19294

3D printed Microblivion II frame by dave c fpv https://www.thingiverse.com/thing:3792194
Frame printed in PETG, 100% infill.
19x19 Sanchez pod

1306 4000kv motors, Flies awesome on 4S 450-650mah

Photos

Part List

Frame	The Microblivion II by Dave_C_FPV (8 builds) Thingiverse.com	See Site
Flight Controller	MAMBA STACK F411 /134 Dshot600 4S NANO (17 builds) Diatone.us	$39.99
Motors	4 x EMAX 1306 RS1306 Version 2 RS1306B 2700KV 4000KV Brushless Motor 3-4S For RC Drone Multi Rotor (16 builds) Banggood.com	$47.56
Propellers	HQProp T3X3 Biblade PC Propeller (Set of 4) (15 builds) Airbladeuav.com	$1.89
FPV Camera	Caddx Turtle V2 1080p 60fps FOV 155 Degree Super WDR Mini HD FPV Camera OSD Mic for RC Drone (74 builds) Banggood.com	$71.28
FPV Transmitter	Eachine NANO VTX 5.8GHz 48CH 25/100/200/400mW Switchable FPV Transmitter Support OSD/Pitmode/IRC Tramp (53 builds) Banggood.com	$14.90
Antenna	URUAV Micro UXII Stubby RHCP Mini FPV Antenna 1.6dBi 5.8Ghz U.FL IPEX IPX For FPV Racing Drone (19 builds) Banggood.com	$15.99
Receiver	TBS Crossfire Nano Rx - FPV LONG RANGE DRONE RECEIVER (1506 builds) Team-blacksheep.com	$24.95
Batteries	CNHL MiniStar 14.8V 4S 450mAh 70C LiPo Micro Battery - XT30 (14 builds) Racedayquads.com	$9.98
Hardware	Banggood.com (5 builds) Banggood.com	See Site
Misc Parts	Special lens for turtle V2 Caddxfpv.com	$8.50
Misc Parts	0.7g Super Mini WS2812B RGB5050 4 Bit Colorful LED Strip for Naze32 F3 F4 Flight Controller RC Drone (12 builds) Banggood.com	$3.37

Show stores (7)

Like Copy Part List Follow irmanhilmi

Discussion

Jodie Froster Aug 16, 2019

Clean!
Also, how much does the frame flex when you runnin them gunz?

irmanhilmi Aug 16, 2019

It flexes quite a bit actually, since it's PETG. I prefer printing frames in PLA since they're stiffer but this one is a bit too thin for PLA.

Dave_C FPV Aug 15, 2019

Again a really nice and clean build! But also there motors are much bigger than what I intended the frame for! Let me know how the frame handles them :-)

irmanhilmi Aug 16, 2019

Thanks. As expected (similar to the CF frame and 5mm Sanchez that I printed for my previous build), the extra weight and power sorta makes the quad flies really awesome (better hang time) but made the whole frame prone to breaking easily. Both the printed 5mm Sanchez (PLA) and Microblivion II (PETG) broke on crashes on grass, will try the Calimero now. I might have to start using 1404s tho, these Emax 1306 has really tiny wires near the windings which break really really easily.