Mixuko Master

By eenoo on Mar 21, 2016

2  251  4

Really enjoyed this build. Great challenge! First time using the RROSD and I have to say its really great. So easy to wire and set up the OSD.

I've swapped some parts since the build has finished, but I'll update it when i swap frames!

I build custom multicopters, from aerial rigs to racing/freestyle. Message me on twitter @Tailored_Quads for more info. I also offer custom designed/cut frames, 3d printed parts, and hydrodipping!

Photos

Part List

Frame

Mixuko 5 (7 builds)
Shendrones.myshopify.com
$70.00

Flight Controller

Naze32 Acro FunFly Rev6C
Multirotorjunkies.com
$25.00

ESCs

4 x FPVHQ | Your FPV Headquarters (3 builds)
Fpvheadquarters.com
$59.96

Motors

4 x EMAX Cooling Series Multicopter Mot... (4 builds)
Hifpv.com
$79.96

Propellers

2 x 10 sets - ORANGE/BLACK Gemfan 5030 2-Blade Multirotor (Total Qty = 40 props)
Thebulkpropguy.com
$52.00

FPV Camera

RunCam PZ0420M (9 builds)
Shop.runcam.com
$30.99

FPV Transmitter

FX796T 600mW Video transmitter
Rotorgeeks.com
$40.00

Antenna

ImmersionRC 5.8 GHz SpiroNET Antenna Set RHCP (SMA Connector) (18 builds)
Getfpv.com
$39.99

Receiver

FrSKY Naked X4R-SB Receiver (19 builds)
Rotorgeeks.com
$38.33

Batteries

3 x BONKA POWER 1600MAH 3S 65C/70C XT-60
Bonkausa.com
$74.97

Power Distribution

RROSD Pro V1 (25 builds)
Redrotorrc.com
$10.00

Radio

FrSky Taranis Plus - Transmitter (4 builds)
Alofthobbies.com
$189.00

Misc Parts

Standoff Kit for Flight Controller and PDB
Multirotorjunkies.com
$5.00

Misc Parts

XT-60 Female with 14AWG Silicone wire 10cm
Multicopterbatteries.com
$2.49

Misc Parts

4 x Replacement Standoffs
Shendrones.myshopify.com
$4.00
Show stores (12)

Discussion

Sign in to comment

Whiffles   Mar 21, 2016  

Photos turned out great! Not bad for a first build! Now how is your stick control? ;)

eenoo   Mar 21, 2016 

this thing is FAST.. like scary fast for a first build. i get nervous each time i take it out that i'll pump the throttle and it will be lost forever.

Whiffles   Mar 21, 2016 

Watching all these FPV videos makes it look so easy doesn't it?

eenoo   Mar 21, 2016 
1

yup. it was very much a "wait wtf how were they doing that" when i got to the park haha.

Guides & Reviews

28 1,316  11
19 days ago

Until recently GoPros were delegated to larger quads. A typical GoPro weighs around 125g and we've only recently begun to mount them on 3" cinewhoops. Even that is a stress on the motors. Now we've got the "GoPro Lite". Remove the battery, displays and casing and you're left with a small, lightweight board and sensor. Wrap it in protective TPU casing and you've got a 30g micro GoPro. The Hero6 is..

Read more
43 4,857  47
May 05, 2020

This guide will walk you through the process of building your first FPV quad. The goal with this design was to build a low-cost, lightweight quad, yet powerful enough to safely carry a GoPro in close proximity areas. I chose these parts to minimize the amount of soldering at no cost to the quality. A typical build requires around 30 solders while this only needs 25. It's not a huge difference, but..

Read more